Decking really is a multipurpose outdoor surface. You can either build your deck as a stand-alone feature to take advantage of the gardens sunniest spot, or extend your internal floor space by attaching a deck to the front, side or back of your house. This arrangement looks fantastic when the deck is linked to the house by a set of French or folding sliding doors.
A decking project is very heavy on materials. To give you an idea, the main frame for the 4.5m x 3.3m deck we built for this particular feature has 400mm gaps (centres) to take the decking boards. This took 48 linear metres of wood to build. We had to use 175mm x 50mm section timber to take the deck up to the interior floor height of the house. It may well be the case that your project might not need anywhere as deep a section (100mm x 50mm section timber is often used) but whatever wood you end up buying, make sure that it is has been pressure treated for outdoor use, or thoroughly soaked in wood preserver first.
This project also took 36 deck boards and 800 screws – so you can see why it makes financial sense to build the deck yourself. As an approximate guide, a professional will charge between £250-500 to build a deck of similar dimensions.
1. Work out where you want to build the deck and compress any loose soil with a thumper or a heavy roller.
2. Lay weed-control fabric over the whole site to stop unwanted greenery from poking through and ruining the finished appearance of your decking.
3. Lay concrete slabs at the corner and centre points of the space you want to deck. The slabs provide a solid, load-spreading foundation for the deck and keep the wooden frame clear of the damp ground. Put a straight piece of wood on top of the slabs and check for level. Get the level as close as you can now by adding more slabs, if necessary. Other options for this foundation part of the job include concreting pressure-treated wooden posts in the ground at regular intervals to support the frame this is particularly useful for creating a level deck on a sloping site. Dedicated deck blocks that are slotted to take the joists of the frame are also available.
4. Make up a simple box frame that will allow the decking to overhang by the thickness of a board at each edge (around 32mm but check the thickness of the boards you are using).
5. Lay the joists inside the frame so that they have 400mm gaps between them.
6. Nail the joists in place. A nail gun comes in very handy for this part of the job. Most tool hire outlets stock them.
7. Once the main frame is built, check it for level. If the frame needs lifting by a small amount to make it level, sections of slate or even floor tile can be inserted where necessary.
8. Make up some 600mm pointed stakes from 25mm x 50mm timber. Treat these with a couple of coats of wood preserver and hammer them in at eight inside corners around the frame. Screw through the stakes into the frame to prevent the structure moving around.
9. Measure, cut and fit noggings staggered along the centre line of the frame. These provide extra strength.
10. For this project we decided to run the outside edges at 90 degrees to the main decking planks that were to run parallel with the back of the house. To get this attractive effect to work well, youll need to mitre the point where the decking planks meet. A manual mitre saw is available quite cheaply from most DIY stores. Lay the planks roughly in position before you cut them and then put a pencil line across the plank in the direction you want the mitre to be. Set the saw to 45 degrees and make sure it is pointing in the same direction as the pencil line; insert the plank and cut. Repeat for the adjoining plank.
11. With the inner corners mitred you can now start to lay the decking planks. Fix the planks 5mm apart with two screws at each joist.
12. Once the decking planks are fixed, mitre the outside corners using the method described in step 10. Plane and sand a rounded edge on the outer corners (inset).
13. Fix a decking plank to the front, back (if seen) and sides of the frame. The face of this plank should fit flush with the edge of the outer panels.
14. If there’s a big drop off the deck onto the garden, you can easily add a step. Make up a framework wide enough to take two decking planks. If you want to face the vertical part of the step with decking, reduce the width of the frame by the thickness of the deck plank you are using.
15. Level and fix the frame all round the deck.
16. Make up stakes (see step 8) and hammer in place. Screw through to the frame to secure the framework.
17. Mitre and lay the decking planks for the steps and fix in place with two screws at every joist. Finally, screw decking panels to the front face of the step to create a neat finish.